Kreg Pocket-Hole Jig 320 with Classic 2 Inch Face Clamp (KPHJ320-22) vs Kreg Pocket-Hole Jig K4
Do you want a portable modular jig or an integrated bench setup?
Products compared
ASIN B0B15KFCDW
Kreg Pocket-Hole Jig 320 with Classic 2 Inch Face Clamp (KPHJ320-22)
You want modular hole spacing and a separate-clamp workflow.
Last observed offer
$49.00
- Confirm offer eligibility on Amazon
Price checked
Observed condition: new. Coupon and subscription requirements unverified.
ASIN B001DYFISG
Kreg Pocket-Hole Jig K4
You want a bench setup with its own workpiece clamp.
Last observed offer
$99.00
- Confirm offer eligibility on Amazon
Size: ()
Price checked
Observed condition: new. Coupon and subscription requirements unverified.
Prices are per listed package. Pickoryx may earn a commission from qualifying purchases through the paid Amazon links on this page, at no added cost to you.
Published by Pickoryx · Published 2026-10-12 · Source checked 2026-10-12 13:18 UTC
The main trade-off
Reconfigurable guides versus an integrated clamp and fixed guide combinations.
Quick verdict
Choose the Kreg 320 clamp kit for a portable, reconfigurable setup. Choose the K4 if an integrated bench clamp and fixed guide combinations better match your work; its removable guide also handles repairs.
Choose Kreg Pocket-Hole Jig 320 with Classic 2 Inch Face Clamp (KPHJ320-22) if
- You want modular hole spacing and a separate-clamp workflow.
Choose Kreg Pocket-Hole Jig K4 if
- You want a bench setup with its own workpiece clamp.
When the recommendation changes
- Repair work alone does not rule out the K4.
- Material outside the supported thickness range needs another solution.
The differences that matter
| Decision point | Kreg Pocket-Hole Jig 320 with Classic 2 Inch Face Clamp (KPHJ320-22) | Kreg Pocket-Hole Jig K4 |
|---|---|---|
| Workholding | Portable jig secured directly to the workpiece with a separate clamp.[1, 3] | Integrated rear toggle clamp; base can be screwed or clamped to a bench.[2] |
What this changes: Choose according to where you want to hold the work, rather than assuming either jig drills better.[1, 3, 2] The better fit depends on your priorities | ||
| Hole Layout | Two guides twist apart; removing the spacer changes their spacing.[1, 3] | Three fixed guide holes: B/C for 1–2-inch boards, A/B for 2–3 inches, A/C for 3–4 inches.[2, 4] |
What this changes: The 320 changes the guide assembly; the K4 changes which holes you use. Wide panels still require repositioning.[1, 3, 2, 4] The better fit depends on your priorities | ||
Best for your routine
Moving between project locations
Best fit: Kreg Pocket-Hole Jig 320 with Classic 2 Inch Face Clamp (KPHJ320-22)
Based on listed features, not comparative testing.
The portable 320 suits this preference; you must position and secure it at the workpiece.
Preparing loose boards at a bench
Best fit: Kreg Pocket-Hole Jig K4
Based on listed features, not comparative testing.
The K4 suits an integrated station; allow access to its rear clamp.
Value and trade-offs
One or both observed offers have eligibility conditions, so no unrestricted price difference is shown.
Pay more only for the setup you will actually use.
Price history is insufficient to assess purchase timing.
Limitations
- This comparison covers the KPHJ320-22 face-clamp kit and standard K4, not the bare 320 or K4 Plus/Master packages.
- No comparative drilling-speed, accuracy, joint-strength or durability testing was performed.
- Secure the jig and workpiece before drilling; never hand-hold the guide. Follow the drill manufacturer’s instructions and use eye, hearing and respiratory protection.
Questions shoppers ask
Does the 320 only work at its three labeled thicknesses?
No. Use its thickness gauge and manual’s range-based screw chart for intermediate thicknesses. Set the stop collar too; the three labels are not three exclusive material sizes.
Is the K4 bench-only?
No. Its removable guide has a repair procedure, as does the 320. Check access for the guide, drill and secure fastening before choosing either for an assembled project.
How do the K4 guide pairs map to board width?
The manual specifies B/C for 1–2-inch widths, A/B for 2–3 inches and A/C for 3–4 inches. Follow its layout guidance when repositioning across wider panels.
Methodology and sources
Compared documented workholding, guide configurations and setup instructions for the US models.
AI assisted source research, drafting and editing. Pickoryx did not conduct hands-on testing.
View 4 sources
- 1.Kreg Pocket-Hole Jig 320: product detailsKreg Tool · Official specifications · Source checked 2026-10-12 13:17 UTC
Evidence used on this page
- Product details and specifications: Portable 320 hardware, removable spacer and material range. Bare-jig page; not the -22 package list.
- 2.Kreg Pocket-Hole Jig K4: product detailsKreg Tool · Official specifications · Source checked 2026-10-12 13:17 UTC
Evidence used on this page
- Item K4; product details and specifications: Integrated clamp, bench mounting, three guides and thickness settings.
- 3.Kreg 310/320 North American owner’s manualKreg Tool · Official specifications · Source checked 2026-10-12 13:17 UTC
Evidence used on this page
- PDF pages 2, 7–11; 4/2019 NK9398V1: Clamping, guide configuration, repairs and thickness-range chart.
- 4.Kreg K4 North American owner’s manualKreg Tool · Official specifications · Source checked 2026-10-12 13:17 UTC
Evidence used on this page
- Printed pages 2, 4–9; 05/2023 112416 V1: Setup, guide pairs, repair use and safety.